BidTroller/User guide

Fence scope, fence pages and takeoff

If your company has workflow turned on, BidTroller reads the fence work out of a job’s bid documents so you don’t have to open the plans and specs to see what the job is. Most of it comes from the text BidTroller pulled from the job’s files. Once BidTroller turns measuring on for your company, it also measures the fence drawn on the plan sheets (see Measured from the drawings below); every measured length is marked as scaled from a drawing.

Fence scope of work

A few short lines that say what the fence work is, the way an estimator writes it:

  • 1,000 LF 8' chain link · 3 gates
  • 625 LF 6' wood perimeter fence
  • (1) wood trash enclosure
  • Remove 300 LF existing chain link
  • Alt 1: 400 LF 6' ornamental steel

How to read them:

  • New fence comes first, biggest run first. The gates ride on the first line; a job with gates and no fence lists the gates on their own line.
  • Removal, remove and reset, temporary fence and each bid alternate get their own line.
  • ~ in front of a number means check it: the documents were unclear, two sources disagreed, or some of that fence had no quantity.
  • length not stated (or count not stated) means the documents name that fence but give no quantity. Measure it from the plans.
  • (scaled) after a length means BidTroller measured it from the fence lines drawn on the plan sheets instead of reading it in the documents (only once measuring is on for your company). It always has a ~: check it against the plans. A fence type the documents name with no length takes the measured length of the matching drawn fence; drawn fence with no matching type gets its own line.
  • No fence found in the plans means BidTroller read the job’s documents and found no fence spec section, fence or site plan sheet, or bid schedule line for fence, gates or guardrail. Look at the drawings yourself before passing on the job: fence that is only drawn, with no words, isn’t found.
  • At most six lines; anything more is counted on the last line and listed in the Takeoff section.

Where you see it:

  • On the Opportunities list, one line under the job’s name: Fence scope: followed by the lines run together. Hover over it to read all of it. Jobs not read yet show nothing.
  • On the job page, a Fence scope of work box under the job’s details, with a link down to every item with its page and quote. Once a job has a finished takeoff, the box also has the Scope letter (.xlsx) button and, when plan sheets were measured, Marked-up plan (PDF), the same downloads as in the Takeoff section.

Ask the plans

Under the fence scope box on every job page, Ask the plans lets you ask a question in plain language about the job’s fence, gates, railing, netting or related scope, for example What height is the fence along the north side? or Who furnishes the gate operator?

  • The answer is drawn only from the job’s fence pages: the fence spec sections, fence and site plan sheets, and bid schedule lines BidTroller found in the documents’ text. It never uses general knowledge of fence work, and it never measures.
  • Each answer lists where it was found: the quoted words, with a link that opens the file at that page. Quote not found on that page means BidTroller could not match the quoted words to the page text; read the page yourself.
  • When the documents don’t answer the question, the answer says The documents don’t answer this. A job with no fence pages, or no readable files, gets that answer without reading anything.
  • The latest ten questions on the job are kept under Earlier questions on this job, for everyone at your company.
  • Owners, admins and estimators can ask; viewers can read earlier answers. An answer takes up to a minute. A company can ask 20 questions an hour and 100 a day. Questions don’t count against the monthly fence scope limit below.

When BidTroller reads a job

  • On its own, every hour: open jobs (New, Reviewing, Pursuing or Bidding, bid date still ahead or not stated) above your company’s threshold that have at least one file BidTroller could read. The threshold is set by your owner or admin on Admin › Fence scope (/app/admin/fence-scope): by score band when scoring is on for your company (BID jobs only, the default; BID and REVIEW; or every open job), otherwise by fit (Likely only, the default; or Likely and Possible). The admin can also turn the automatic reading off; Get fence scope still works then. Each job is read once. It is read again only when new files arrive after that, such as an addendum. Soonest bid date first.
  • When you ask: on the job page, Get fence scope reads any job with readable files, whatever its fit. On a job already read it says Run again. Owners, admins and estimators can use it; viewers can’t. It takes up to two minutes; the button says Reading the plans… until it’s done.

Jobs with no readable files (often jobs that came only from a paid bid site, where BidTroller has no plans) can’t be read. The box says so.

The monthly limit

Your company has a number of runs a month, 150 unless BidTroller set another number for you. Runs on its own and Get fence scope runs count together. A run that finds no fence pages doesn’t count. The job page shows how many are used, for example 12 of 150 used this month. When they’re used up, Get fence scope is greyed out and the hourly reading stops until the 1st of next month (Central time). To change your limit, send it as Idea or request on the Feedback page.

Fence pages

When a job has searchable files (see Files in A job page), the Fence pages section lists, for each file, the spec sections and plan sheets that likely cover fence. Each one shows the section number or sheet, its title, a link that opens the file at that page, how sure BidTroller is, and the words it went by. A file with nothing found says No fence sections or sheets found.

It is found from section headings and sheet titles, so treat it as a shortcut to the right pages, not a complete list.

Takeoff

Once a job has been read, a Takeoff section further down the job page shows the detail behind the fence scope:

  • A short summary, then a table of totals by type (for example chain-link fence, gates, railing), with the quantity, how many items make it up, and how many need a check.
  • Warnings the documents raise, like demolition, rock, coatings, grounding or gate operators, each with its page.
  • Scales named in the plan text.
  • Every item with its source: each quantity with the page and the exact words it came from, whether it came from the bid schedule, a spec or a plan note, and how confident BidTroller is. Items marked needs check say why.
  • Pages sent to the model: which pages were read. If a job had more fence pages than fit in one run, a yellow note says the takeoff may be incomplete.

Measured from the drawings

Once BidTroller turns measuring on for your company, each takeoff run also measures the fence drawn on up to three of the job’s plan sheets: sheets whose title or notes mention fence first, then site plans. It uses the plan sheets the text search found, in the same run, so it doesn’t count against the monthly limit again; it adds up to about a minute and a half to the run. Until it’s on, the Takeoff section shows only quantities stated in writing.

For each sheet BidTroller:

  • finds the scale: the scale note under the drawing or in the title block, the graphic scale bar, and any calibration saved in the PDF, checked against the drawing’s own dimension strings. When they disagree (a sheet printed at a different size keeps its old scale note; the bar shrinks with the drawing), it uses the one the dimensions agree with and says so. On a sheet with an overall plan and an enlarged plan at different scales, each run uses the scale of the drawing it’s in, and only the most detailed drawing is counted. On sheets whose lettering is drawn as lines rather than text, it reads the printed scale from the sheet image.
  • finds the fence lines: lines that carry a fence symbol (x’s, little boxes, circles or dots), and lines drawn in their own colour, weight, dash pattern or a CAD layer named for fence. Where the sheet’s legend shows a sample of a linetype, the words beside it name that fence type. The model then decides, from the legend, keynotes and callouts, which of those lines are fence and what type each is. A line identified only by a keynote tag whose note is on another sheet (a pool barrier on a floor plan, say) is measured and marked Check with low confidence, rather than left out. Silt and erosion-control fence, fence marked existing to remain, property lines, walls and legend samples are not counted.
  • measures them: lines drawn twice count once, dashed lines count through their gaps, and the length is scaled to feet. A line drawn as a narrow band, two parallel edges the way walls and curbs are drawn, is measured along one edge only and marked Check when it is counted as fence. Where it runs beside fence already measured, it adds nothing. A heavy line drawn over the fence, such as an earlier highlighter markup, adds nothing where it covers the fence. When an addendum reissues a sheet (the same sheet number in two files), only the later file’s sheet is counted.
  • finds the gates: site plans often draw a gate with no symbol, the fence line simply crossing a drive or walk, so BidTroller looks along each measured fence line for places a gate could be (the fence crossing a drive or walk between two curbs, two fence ends facing each other across a gap, a swing arc or a V-shaped double-gate symbol) and the model looks at a close-up of each one and says which are gates. Some sheets mark every gate with just the word GATE and no size. Where that word sits at a gap in a wall or screen wall, BidTroller sizes the gate from the wall’s end to the next line. Where it sits beside the fence and a short gate line is drawn on the fence there, BidTroller sizes the gate along that line, from the curb on one side to the curb on the other (or to the end of the gate line where no curb crosses it), and the model checks it like any other opening. Where it sits beside the fence and BidTroller can’t size the opening, the gate is still counted, with no size and marked to check, and the fence length there still includes it. Each gate it keeps is listed on its own with its width scaled from the drawing (for example 14' slide gate), and the stretch of fence line drawn across it is taken out of the fence length. Gate callouts on the sheet are used to name the gates; a callout that matches no gate on the drawing is listed in the notes to check. When no gate is found on the drawing, the gates called out on the sheet are listed instead, with the sizes they state.

When two of the measured sheets show the same ground (two enlarged plans of one site that overlap, an overall plan and an enlarged one, or two copies of one drawing), fence drawn on both is counted once. BidTroller lines the sheets up by the words printed on both near the fence, such as dimensions and labels, then counts the shared fence on the more detailed sheet, or the first one when they are at the same scale. A gate drawn on both is counted once too. The other sheet’s notes say how many feet were left out there and which sheet they are counted on. On the marked-up plan that fence still shows on the other sheet, as a gray dashed line labelled counted on and the sheet's number, so a run doesn't look cut short there. Sheets that share too few words to line up are each counted in full.

On the job page, Documents vs drawings in the Takeoff section puts the two side by side in one table, one row per fence type:

  • In the documents: the quantity the bid schedule, spec sections or plan notes state in writing, or not in the text when only the drawing has it.
  • From the drawings: the length scaled from the drawn fence lines, with a link to each sheet it came from, or not found when no drawn line matched.
  • Difference: how far the drawing is from the documents, as a percentage of the documents’ number.
  • Check: what to look at. A row is shaded when the two are more than 10% apart, or when only one side has the type. It also says which number the scope letter uses: the documents’ number when they give one, the drawing’s when they give none.

The last row, All gates, compares the number of gates the documents list with the gates found on the drawings and the sizes scaled from them. A drawn type is matched to a stated one by its words, the same way the scope letter matches them. Counted items such as a trash enclosure aren’t measured, so they show the documents’ count only.

Below the table, Each sheet: scale, gates and notes shows the scale used and where it came from, the gates, and anything to check, such as two scales that disagree or fence the sheet mentions but doesn’t draw. A type marked Check says why. A scanned sheet (a picture with no line work) gets only a rough visual estimate, marked as one. Without measuring, the Takeoff section shows the stated quantities in a table of their own.

Downloads at the top of the Takeoff section:

  • Download items (.csv): every item in one flat file, with a link to each source page.
  • Download workbook (.xlsx): an Excel workbook with four sheets. Summary has the job, agency, bid date, run date and the totals by type (quantity, unit, basis, items, items with no quantity, items to check); Items has one row per item with its type, height, scope, quantity, unit, basis, confidence, needs-check flag, file, page, quote and link; Warnings and Pages used list the rest. When the plan sheets were measured, the Summary also lists the measured totals with the basis scaled from drawing (stated quantities say stated in writing), and a fifth sheet, Measured, has one row per sheet and fence type: the length, runs, the scale used and where it came from, confidence, what to check and a link to the sheet, then the gates and notes.
  • Marked-up plan (PDF): in the Documents vs drawings box, once sheets were measured. The measured sheets copied out of the documents with each measured fence run traced in red and its footage beside it (a letter per fence type), gate callouts circled where BidTroller could place them, and a legend box in the corner with the scale used, the total length of each type, the gates (with the width scaled from the drawing when the sheet gives none) and the notes. Fence drawn on this sheet but counted on an overlapping one is a gray dashed line. Every number on it is scaled from the drawing; check it before you price the job.
  • Scope letter (.xlsx): your company’s scope letter with this job’s fence, gate and railing lines, price and working days left blank. Once measuring is on for your company, it uses measured lengths for fence the documents give no length for, and the gates found on the drawing when the documents list none. See Scope letter and Google Drive.
  • Fence spec sections (PDF): the fence specification pages BidTroller read, copied out of the documents into one PDF, with a first page listing the file and page each one came from. Shown when the run read spec pages.
  • Fence plan sheets (PDF): the same for the fence plan and detail sheets. Shown when the run read plan sheets.

The PDFs hold only the pages the text search found, at most 300 pages, and skip a file over 48 MB (the first page says so). Bid schedule pages are not in either PDF; the Items sheet and the takeoff link to them.

What it can’t do yet

  • Until measuring is on for your company, the quantities are only the ones the documents state in words: a bid form, a spec section, a plan note or legend. When the only quantity is a wall or run length the plan states, BidTroller uses it with a ~ and says what it measures, and fence that is only drawn shows length not stated.
  • Measuring reads at most three plan sheets a run, and only sheets the text search found. Fence on other sheets isn’t measured.
  • Fence that a note puts on something else, such as “fence on top of the retaining wall”, is not drawn as a fence line, so it isn’t measured; the notes say when the sheet mentions fence it couldn’t find.
  • A gate BidTroller didn't find on the drawing stays inside the fence length, and a gate it found that isn't one (a gap for a planted island, say) takes a few feet out. Check the gate count and sizes against the plans before you price the job.
  • When fence types differ only by tiny symbols and the sheet has no legend sample, BidTroller can mix types up; those are marked Check.

Check every number against the plans before you price the job.